top of page
Search

Bent Garage Door Track: Repair or Replace?

Nov 11
4 min read

Updated: 16 hours ago

A bent garage door track is not a job to tackle yourself in most cases. If the track is dented, kinked or pulled away from the wall, stop using the door and have a technician look at it, because a door running in a damaged track can jump out and come down hard. A small cosmetic ding is a different story, and this guide explains how to tell which one you have.

What does a bent garage door track look like?

A bent track shows up as a visible dent, kink or twist in the metal, a gap where the track has pulled away from the wall, or a section that is no longer straight when you sight along it. You may also see rollers sitting at an odd angle, scrape marks on the steel, or a door that tilts to one side as it moves. Any of these means the rollers are no longer travelling freely.

What causes a garage door track to bend?

Most bent tracks come from an impact or from the door coming off its track. The usual causes are:

  • A vehicle, bike or heavy object striking the door or the vertical track

  • A door that jumped off the track and was forced up or down

  • Loose brackets or lag screws that let the track drift and rub the rollers

  • A broken cable that lets one side of the door drop and twist the track

Is it safe to keep using a door with a bent track?

No, it is best to stop using the door until it has been checked. A door can run on a slightly bent track for a while, but the rollers can bind or pop out at any moment, and a heavy door that drops suddenly can hurt someone or crush a car. If the door is stuck partway open, do not pull the emergency release cord, because the door may fall. Keep people and vehicles clear and call for help. Our guide on a door that has come off its track is here: garage door off track.

Can a bent garage door track be straightened?

Sometimes, when the bend is minor and the metal has not creased. A technician can work out a shallow dent with the right tools and then realign the track so both sides match. A sharp crease, a kink or a stretched section usually calls for replacement, because bent steel rarely returns to a true shape and keeps catching the rollers.

When does the track need to be replaced?

Replacement is the safer choice when the damage goes beyond a light dent. Look for these signs:

  • A creased or kinked section of metal

  • Damage at the curve where the vertical track turns into the horizontal one

  • Torn or enlarged mounting slots where the track bolts to the wall

  • A twisted track that no longer lines up with the one on the other side

Can I hammer the track flat myself?

It is not recommended. Striking the track can crease it further or leave a rough spot that catches the rollers even if it looks straight. The track also carries the weight of the door under spring tension, so working near it with the door raised is risky. Leave the springs, cables and brackets at the bottom of the door alone, since they are under high tension.

How can I check whether my tracks are aligned?

Compare the left and right sides. Both vertical tracks should be straight and parallel, with the same small gap between the track and the rollers on each side. A visible difference points to a shifted or bent track. Checking that the mounting bolts are snug is a fair homeowner task, but if the door is crooked or noisy, the problem may be a worn part as well, such as the ones covered in our garage door roller guide.

What happens during a track repair visit?

The technician checks the door balance, cables, rollers, hinges and both tracks, then straightens or replaces the damaged section, resets the alignment and tests the door with the opener. Bent tracks often come with other damage, so the rest of the hardware is inspected before the door is put back into use. If the door also closes crooked, see our page on a sagging or uneven garage door.

How do I keep a track from bending again?

  • Keep bikes, bins and ladders well away from the door's path

  • Check that the track bolts are snug a couple of times a year

  • Replace worn rollers and frayed cables before they let the door twist

  • Take the car slowly in and out, and keep the door sensors working

Need help with a bent garage door track?

If the track was bent by an impact, read what to do after backing into your garage door.

Modern Empire Doors, at 138 Yorkland St in Richmond Hill, is available 24/7 at 647-323-1826 and has served the GTA since 2018. We are top rated on Google. Send us a photo of the door from inside and outside, with the damaged section in view, and we can tell you whether the track can be straightened or needs replacing.

 
 
 

Comments


Commenting on this post isn't available anymore. Contact the site owner for more info.
  • Facebook
  • Instagram
  • Yelp

Contact Us

(647)-323-1826

Modern Empire Doors: Let us get the door for you.

© 2026 Modern Empire Doors. All Rights Reserved.

Thank You For Your Message!

bottom of page
Call nowText a photo

Modern Empire Doors

Garage doors, garage door openers, front doors, patio doors and windows.

Sales, installation and repair across the Greater Toronto Area.

Visit or call

138 Yorkland St, Richmond Hill, ON L4S 1J1

647-323-1826

Open 24/7, including weekends.

Serving the GTA since 2018. Our doors are made in Canada and carry a limited lifetime warranty.